minor updates clubdat 11 Feb 2018

DTObs.py

@@ -92,8 +92,11 @@ class DTObservationProgram(Ui_mainWindow):
         logger.info('Initialization of DTObsGUI')
         self.demo = config.getboolean('TestConfig','demo')
         logger.debug('Demo status is: {}'.format(self.demo))
-        if self.demo == False:
-            self.myDT = telescope(setmode='J2000', consoleHost='consoledemo.dmz.camras.nl')
+        if not self.demo:
+            if True or self.actualconsole:
+                self.myDT = telescope(setmode='J2000', consoleHost='console')
+            else:
+                self.myDT = telescope(setmode='J2000', consoleHost='consoledemo.dmz.camras.nl')
             self.telescopeMode = 'J2000'
             self.telescopeOffset = None
         else:

_impactbatch.log

+iMPACT Version: Oct 13 2013 08:43:40
+
+iMPACT log file Started on Sun Feb 11 13:02:13 2018
+
+Preference Table
+Name                 Setting             
+StartupClock         Auto_Correction     
+AutoSignature        False               
+KeepSVF              False               
+ConcurrentMode       False               
+UseHighz             False               
+ConfigOnFailure      Stop                
+UserLevel            Novice              
+MessageLevel         Detailed            
+svfUseTime           false               
+SpiByteSwap          Auto_Correction     
+AutoInfer            false               
+SvfPlayDisplayComments false               
+AutoDetecting cable. Please wait.
+*** WARNING ***: When port is set to auto detect mode, cable speed is set todefault 6 MHz regardless of explicit arguments supplied for setting the baudrates
+ Using windrvr6 driver.
+Connecting to cable (Usb Port - USB21).
+Checking cable driver.
+File version of /opt/Xilinx/14.7/ISE_DS/ISE/bin/lin64/xusbdfwu.hex = 1030.
+ libusb-driver.so version: 2011-12-12 16:47:45.
+Please run `source ./setup_pcusb` from the/opt/Xilinx/14.7/ISE_DS/ISE//bin/lin64 directory with root privilege to updatethe firmware. Disconnect and then reconnect the cable from the USB port tocomplete the driver update.
+Cable connection failed.
+INFO:Cse - The fxload application is not installed. This application is required   when using the Platform Cable USB. This warning should be ignored if you are   using the Parallel Cable III or Parallel Cable IV. Please download and   install the fxload-2002_04_11 package. Note that root access is required to   perform the installation.
+Connecting to cable (Parallel Port - parport0).
+ libusb-driver.so version: 2011-12-12 16:47:45.
+ parport0: 
+ parport1: 
+ parport2: 
+ parport3: 
+ LPT1 Base Address set from env variable = 0.
+ LPT base address = 0000h.
+ LPT1 Ecp Address set from env variable = 400.
+ ECP base address = 0400h.
+Cable connection established.
+Identifying chain contents...'0': : Manufacturer's ID = Xilinx xc3sd1800a, Version : 0
+INFO:iMPACT:1777 - 
+   Reading /opt/Xilinx/14.7/ISE_DS/ISE/spartan3adsp/data/xc3sd1800a.bsd...
+INFO:iMPACT:501 - '1': Added Device xc3sd1800a successfully.
+----------------------------------------------------------------------
+----------------------------------------------------------------------
+done.
+Elapsed time =      0 sec.
+Elapsed time =      0 sec.
+'1': Loading file '/usr/local/share/backend/pulsar.bit' ...
+done.
+INFO:iMPACT:2257 - Startup Clock has been changed to 'JtagClk' in the bitstream   stored in memory,
+   but the original bitstream file remains unchanged.
+UserID read from the bitstream file = 0xFFFFFFFF.
+INFO:iMPACT:501 - '1': Added Device xc3sd1800a successfully.
+----------------------------------------------------------------------
+----------------------------------------------------------------------
+Maximum TCK operating frequency for this device chain: 0.
+Validating chain...
+Boundary-scan chain validated successfully.
+'1': Programming device...
+ LCK_cycle = NoWait.
+LCK cycle: NoWait
+done.
+'1': Reading status register contents...
+CRC error                                                                  :        0
+IDCODE not validated while writing FDRI                                    :        0
+DCM matched                                                                :        1
+status of GTS_CFG_B                                                        :        1
+status of GWE                                                              :        1
+status of GHIGH                                                            :        1
+value of VSEL pin 0                                                        :        1
+value of VSEL pin 1                                                        :        1
+value of VSEL pin 2                                                        :        1
+value of MODE pin M0                                                       :        0
+value of MODE pin M1                                                       :        1
+value of MODE pin M2                                                       :        0
+value of CFG_RDY (INIT_B)                                                  :        1
+DONEIN input from Done Pin                                                 :        1
+POST_CRC_ERR error                                                         :        0
+SYNC word not found                                                        :        0
+INFO:iMPACT:2219 - Status register values:
+INFO:iMPACT - 0011 1111 1010 1100 
+INFO:iMPACT:579 - '1': Completed downloading bit file to device.
+INFO:iMPACT:188 - '1': Programming completed successfully.
+ LCK_cycle = NoWait.
+LCK cycle: NoWait
+INFO:iMPACT - '1': Checking done pin....done.
+'1': Programmed successfully.
+Elapsed time =     50 sec.

dtobsgui.ini

@@ -2,4 +2,4 @@
 LogLevel: INFO
 
 [TestConfig]
-demo: True
+demo: False